Technical Specifications Breakdown
Key parameters for the 330101-00-12-10-02-05 are listed below for quick reference:
| Feature | Specification |
|---|---|
| Product Type | 3300 XL 8 mm Probe, 3/8-24 UNF thread, without armor |
| Unthreaded Length Option | 00 - 0.0 in |
| Overall Case Length Option | 12 - 1.2 in |
| Total Length Option | 10 - 1.0 metre (3.3 feet) |
| Connector and Cable-Type Option | 02 Miniature coaxial ClickLoc connector, standard cable |
| Approvals | CSA, ATEX, IECEx |
| Probe Tip Material | Polyphenylene sulfide (PPS) |
| Probe Case Material | AISI 303 or 304 stainless steel (SST) |
| Linear Range | 2 mm (80 mils). Linear range begins at approximately 0.25 mm (10 mils) from target and is from 0.25 to 2.3 mm (10 to 90 mils) (approximately –1 to –17 Vdc) |
| Recommended Gap Setting for Radial Vibration | -9 Vdc [approximately 1.27 mm (50 mils)] |
| Incremental Scale Factor (ISF) Standard 5 or 1 meter System | 7.87 V/mm (200 mV/mil) ± 5% including interchangeability error when measured in increments of 0.25 mm (10 mils) over the 80 mil linear range from 0°C to +45°C (+32°F to +113°F) |
| Probe Temperature Range (Standard) | -52°C to +177°C (-62°F to +350°F) |
Industry Applications
Its 2 mm linear range and high sensitivity (7.87 V/mm) enable early detection of shaft misalignment or bearing wear. The robust stainless steel case and PPS tip withstand oil, moisture, and temperature extremes common in oil & gas and power generation.
Installation & Setup Guidance
Mount the probe using the 3/8-24 UNF thread into a compatible bracket or housing. Ensure the target surface is clean and within the recommended gap of -9 Vdc (approximately 1.27 mm). Use the miniature coaxial ClickLoc connector for secure cable attachment. Field wiring should be 0.2 to 1.5 mm² (16 to 24 AWG) three-conductor shielded triad cable, with a maximum length of 305 meters (1,000 feet) between the probe and monitor.
Maintenance & Reliability
The patented TipLoc and CableLoc designs provide 330 N (75 lbf) pull strength, reducing cable fatigue. Inspect the probe tip and cable periodically for physical damage. Avoid exposing the probe to temperatures below –34°C (–30°F) to prevent pressure seal failure. The Viton® O-ring seals differential pressure; contact the custom design department if pressure testing is required.
Compatibility & Integration
This probe is part of the 3300 XL series and works with Bently Nevada Proximitor sensors and monitoring systems. The standard cable length of 1.0 meter (3.3 feet) allows flexible placement near the machine. For extended temperature ranges, the probe tip can operate up to +218°C (+425°F) with the ETR option.
Selection Guide & Purchasing Advice
When ordering, verify the total length option (10 = 1.0 metre) and connector type (02 = ClickLoc). Contact AutoDCSTech for lifecycle status and availability before placing an order.
Troubleshooting & Common Issues
If output voltage is unstable, check the gap setting and target surface condition. Verify cable continuity and connector integrity. For signal roll-off at high frequencies with longer field wiring, refer to the frequency response graphs in the manual. Ensure the probe is not exposed to temperatures below –34°C (–30°F) to avoid pressure seal damage.
Availability & Condition at AutoDCSTech
| Part Number | 330101-00-12-10-02-05 |
|---|---|
| Availability | In Stock |
| Condition | New |
| Warranty | One Year |
| Origin | US |
